IPL/OPT Photon Cosmetology...-manufacture,factory,supplier from China

A photon is an fundamental particle, a quantum of electromagnetic radiation. In quantum subject theory, it is the pressure provider that transmits the electromagnetic force.Light spots/spots are few and a ways betweenLight spot is the contact factor of mild contact skin, distinctive units have specific mild output measurement and shape.

Optical terms for cosmetic instrumentsA photon is an elementary particle, a quantum of electromagnetic radiation. In quantum field theory, it's the force carrier that transmits the electromagnetic force.Light spots/spots are few and far betweenLight spot is the contact point of light contact skin, different instruments have different light output size and shape. Such as color light instrument contact point is generally rectangular, size marked as long x wide (for example: 10mm x 25mm). Generally, the laser output is a dot, and the size is marked as the diameter (e.g., 3mm, 8mm, etc.).

How to install laser engraving machineThe installation of laser engraving machine has the following three steps:1. Installation(1) Insert the control card into the microcomputer PCI slot, tighten the screws, and connect the data cable; Plug in the USB dongle and install the operating software and dongle driver.(2) Connect the laser tube water circulation tube with the anode and cathode conductor, and then put the laser tube clamp ring.

Mode of operation of laserThe laser with different wavelength and different output mode will be absorbed by different tissues or substances after entering the skin and thus produce different action modes. These tissues or substances are called Chromophore.Photothermal action refers to the absorption of laser light into the skin by specific pigment groups and then converted into heat energy. Depending on the duration of the laser pulse and the heat dissipation time of the skin tissue, the heat may spread to the surrounding tissues and cause a wide range of heating (e.g.

The principle of laser generationLASER is written as "Light Amplification by Stimulated Emission of Radiation", which means that by the principle of "excitation emission", the amplification of light waves is generated, which is called "laser". The motion state of electrons can be divided into different energy levels. When electrons transition from high energy level to low energy level, they will release electromagnetic waves of corresponding energy (the so-called spontaneous radiation).

How to prolong the service life of laser tube1 laser engraving machine, cutting machine in the use of laser tube, need to pay attention to the best use of pure cooling water, and keep the water temperature below 25℃.2. Summer temperature is high, it is necessary to pay attention to frequently change the cooling water, found that the temperature is too high, need to stop and rest and replace the cooling water; Winter temperature is low, the machine after the completion of the work, need to put the laser tube internal cooling water, to avoid the laser tube is frozen cracked.3.

Why the laser is weak or has no laser outputWhether the focusing mirror is contaminated: Clean the focusing mirror.Whether the focal length of relief engraving machine equipment changes: readjust the focal length.Whether the optical path is offset: Adjust the optical path carefully.Whether the reflector is contaminated or damaged: Clean or replace the reflector.Whether the laser power supply is powered on: Check the power supply loop of the laser power supply to make it normal.Whether the laser tube is damaged or aged: Replace the laser tube.Whether the laser power supply is damaged: Replace t

How to prolong the service life of laser tube1 laser engraving machine, cutting machine in the use of laser tube, need to pay attention to the best use of pure cooling water, and keep the water temperature below 25℃.2. Summer temperature is high, it is necessary to pay attention to frequently change the cooling water, found that the temperature is too high, need to stop and rest and replace the cooling water; Winter temperature is low, the machine after the completion of the work, need to put the laser tube internal cooling water, to avoid the laser tube is frozen cracked.3.

Precautions for using laser and colored light◇ In the course of optical treatment, the operator should minimize the potential risks to the person present and the possible side effects to the customer◇ During the course of treatment, unauthorized persons are forbidden to enterAll reflective materials and inflammable materials should not be placed in the treatment room, such as mirrors and reflective glass objectsCarbon dioxide extinguisher should be placed in the room◇ Beauty care center should keep the fire outlet unblockedDoors should be kept closed and Windows should be covered with light -

Classification of switching power suppliesSwitching power supplies can be divided into AC/DC and DC/DC. As a secondary power supply, DC/DC converter has realized modularization, and the design technology and production process have been mature and standardized at home and abroad, and has been recognized by users. However, due to its own characteristics, the primary power AC/DC has encountered more complex technical problems and manufacturing problems in the process of modularization.